Skip to content
fix.fmaudio repair

LUFS meter free, in your browser

Find out how loud your recording feels, and how close its peaks come to clipping. Choose a file and this online LUFS meter measures it in your browser.

LUFS METERCHOOSE A FILE
or drop it here · WAV · MP3 · M4A · MP4

Processing runs on your device. Up to 200 MB and 60 minutes. Format support depends on your browser.

What to expect

Cost and privacy
Free, with no account. Processing runs on your device; your audio is never uploaded.
Use it for
Measure integrated LUFS, sample peak, estimated true peak, loudness range and short-term loudness.
Inputs
Browser-readable audio, including WAV, MP3, M4A and the audio from MP4. LUFS requires mono or stereo and at least 400 ms.
Downloads
CSV or JSON readings and available passage measurements. The report contains no audio or original filename.
Limits
Up to 200 MB and 60 minutes, subject to available browser memory.
Keep in mind
It measures the decoded copy, which your browser may resample. It does not change loudness and is not a certified compliance meter.

What these readings tell you

Integrated LUFS estimates the loudness of the whole file using K-weighting and loudness gates. It is useful for comparing finished recordings; it does not show whether two speakers are balanced or whether every word is clear.

Sample peak is the loudest saved sample. True peak also estimates the waveform between samples. This meter uses 4x interpolation for that estimate. It follows the mono/stereo BS.1770 measurement approach, but is not a certified compliance meter. A commercial delivery should also be checked with the destination's approved meter.

The report under the readings shows short-term loudness, the 3 second measurement from EBU Tech 3341, once a second across the recording, with the whole-file reading drawn through it. The loudness range follows EBU Tech 3342: the spread between the 10th and 95th percentile of those short-term values after gating. The quietest and loudest 3 seconds can be played in place, so you hear whether a quiet passage is one speaker, a soft section or a gap.

The browser may resample the recording when decoding it. These readings describe that decoded audio, not untouched file-header data. Measure the final encoded file again, because a lossy export can change its peaks. Files shorter than 400 ms and layouts beyond stereo do not receive a LUFS reading here.

Reference checks you can reproduce

We measured 9 generated signals with this meter and FFmpeg's separate EBU R128 scanner. Both received the same 32-bit float WAV samples, without browser decoding or resampling. These are our own test signals, not an official EBU compliance test set or a certification.

CHECKED OCTOBER 13, 2026 · FFMPEG VERSION 8.1.2

Largest whole-file loudness difference
0.04 LU
Largest estimated true-peak difference
0.62 dB
Largest loudness-range difference
1.02 LU
Each pair reads fix.fm / FFmpeg. FFmpeg's summary is rounded to one decimal place. All cases are mono at 48 kHz unless named otherwise.
SignalIntegrated (LUFS)True peak (dBTP)Range (LU)
Steady 1 kHz, mono-23.00 / -23.0-20.00 / -20.00.00 / 0.0
Same 1 kHz tone in both channels-19.99 / -20.0-20.00 / -20.00.00 / 0.0
Steady 1 kHz at 44.1 kHz-23.00 / -23.0-20.00 / -20.00.00 / 0.0
Steady 100 Hz, mono-24.84 / -24.8-20.00 / -20.00.00 / 0.0
12 kHz starting away from zero-0.57 / -0.6-0.92 / -0.30.00 / 0.0
Same 12 kHz tone with 10 ms fades-0.58 / -0.6-0.92 / -0.90.01 / 0.0
Four seconds of tone, then silence-23.17 / -23.2-20.00 / -20.07.78 / 8.8
Twenty seconds loud, twenty 10 dB quieter-25.60 / -25.6-20.00 / -20.010.00 / 10.0
Tone with a 40 dB quieter middle-23.17 / -23.2-20.00 / -20.07.78 / 8.8
Steady tones check level, channel summing and frequency weighting. The quieter middle and final silence check gating; the two-level signal checks range. The 12 kHz tone has sample peaks below its reconstructed peaks. Differences are calculated from the rounded values shown here.

The tone that starts away from zero differs by 0.62 dB in true peak; with 10 ms fades the difference is 0.02 dB. The tone followed by silence differs by 1.02 LU in range. Boundary and window behavior matter. These checks do not establish accuracy for every transient, codec or sample rate. Use a destination-approved meter for strict delivery and measure the final encoded file.

Download the comparison and signal recipes (JSON). How to reproduce this check explains the command and scope. LUFS, dBFS and dBTP explains what the readings mean.

References: ITU-R BS.1770, Apple Podcasts audio guidance, and Spotify music playback normalization. Platform guidance checked October 1, 2026.

Need a custom loudness target? Use the volume normalizer on tonal.fm, our sister site's free tool. It applies uniform gain within its peak ceiling; reaching a louder target may require compression or limiting.

Questions

Does the meter change my audio?

No. It only measures a decoded copy. It does not change gain, compress, or save over your recording.

Can I download the loudness readings?

Yes. Save a CSV for a spreadsheet or a JSON report for other software. Both include the whole-file readings, available quietest and loudest passages, and short-term measurement windows with units. They describe the decoded recording before any gain change. No audio or original filename is included in the report. Missing readings are blank in CSV and null in JSON. This is an editing reference, not a certified delivery report.

What does the loudness range tell me?

How much the levels vary within the windows counted by the gated range calculation, in LU. Very quiet passages can fall outside that range, so a small number does not prove two speakers are balanced. Play the quietest and loudest measured passages, then adjust individual clips before setting the overall loudness. A single gain change keeps the gap between speakers.

Is -14 LUFS a target for every recording?

No. Spotify describes -14 LUFS for normal music playback. Spoken-word podcasts and broadcast deliverables have different guidance. Use the destination's current specification.

Why is a duplicated mono file louder in stereo?

This loudness measurement sums both channels. Two identical channels measure about 3 LU louder than the same signal in one channel, even if their sample peaks are identical.

Does it upload my file?

The measurement is performed locally in a Worker. The tool sends no audio file or sample data to a server.